MIG-27 Completed


Well she’s done, I know its not a great kit of the subject but I have enjoyed the build a lot. It went together without me wishing I hadn’ bothered starting it so whilst it may not be the most accurate kit around, with the exception of the intakes it was certainly hassle free, which is more than can be said for many kits out there!

Thanks to those that followed along with the build and I hope you like the end result!

Advertisements

Seat detailed


Heres the new and improved seat. I added a back cushion that was made from lead substitute that I usually melt down for nose weights, the seatbelts are PE from the spares box, the ejection pull handle is some styrene rod bent round. I have also put a back on the seat and made some seat rails from more styrene rod that will be used to attach the seat to the newly installed bulkhead, which was fettled from a piece of styrene/plasticard. It’s not fantastic but it should help busy things up I think!

MIG Update



I know I havent posted for a while, things have been a little hectic in the flat so I haven’t had much time at the bench, here is a quick look at the paint on the MiG build now the demarcation has been sharpened up, needs a couple of touch ups etc but its looking ok.

I have also decided on the weapons this ones goingto be carrying, load out is going to be a couple of OFAB-100 on the rear pylons, UB-32 pods on the wing gloves, UB-16 on the outer fuselage pylons and the centre line will carry an external fuel tank. After all, who doesnt like rockets!

So much for keeping it simple



So much for keeping things nice and simple. As I had almost finished the paint I removed the masking tape and blue tack covering the cockpit and it really struck me how poor the cockpit was looking (there isn’t even a control stick) and the seat especially was annoying me, it looked pretty bad and also seems to sit too far forward leaving quite a big gap between the back of the seat and where the none existant bulkhead should be. These photos are from earlier on in the build to illustrate how poor things are looking as standard.

 

East of Scotland Model Show 2017

This weekend saw the annual East of Scotland Model Show put on by IPMS Dundee, which is the club I have recently joined. Unfortunately due to work commitments I was only able to attend for the last hour of the show but still there was plenty to see, a fantastic number of entries to the competition all of which were superb, the club displays from all the attending clubs were all top quality and there were of course plenty of temptations provided by the visiting vendors!

I didn’t grab many photos as arriving straight from work and in somewhat of a rush I only had my phone with me but these are some of my favourite builds from the show, hopefully next year I’ll be able to attend properly and get some builds in the competition myself.

Winging it


It’s finally time to get back to sticking some plastic together! I’ve been working on the Vampire again and have managed to get the fuslage shut and the main parts of the wings together. This was fairly uneventful although I have been left with a small step at one of the wing roots which I am not sure how to address without losing some of the fine rivet engraving etc. I may just have to try and reinstate this after some remedial work is carried out.

MiG 27, Getting shady


Well I can wait no longer, time to get some paint down, this is proving to be a little more difficult than usual as my AS186 chinese compressor keeps overheating, I will strip it down again and see if I can’t get it somewhere near normal, if not I guess the letter to santa will be leaving early this year!

Cockpit complete




Well after what seemed like far too many parts of etch the cockpit is pretty much complete and it’s time to shut the fuselage up, meaning that most of the etch will never be seen again but that’s nothing new is it! Onward!

Intakes done


Progress slowed a little of late on this one but the intakes are looking OK to my eye, I put primer on to see what they looked like in paint and I don’t think they too bad at all considering the size of the step that was there. I left her belly up with the primer drying on the underside last night, which meant I spent a lot of time looking at those dodgy wheel wells. I may throw in some cabling or something to try and add a bit of interest, depends if I can find any reference images or not.