Hasegawa Tritool, File Set Professional Type

Hasegawa Tritool File Set Professional Type
Selection of Files included in the Hasegawa Tritool File set, Professional Type

I decided to treat myself to some new files for modelling as my old ones are looking a little worse for wear so I had a nose about online and I found this Hasegawa set on one of my favourite Japanese vendors on Amazon for a great price so promptly placed the order.

The files arrived in good time as always with this vendor and here they are. I am not sure what makes these the professional type, the vendor did also have the standard type but as there was only around a pound saving I ordered these ones. Nothing to get excited about really is it but still I couldn’t wait to give them ago.

As you can see there’s a good selection of file profiles included in the packet and they are all fantastically sharp, so much so I have found it extremely easy to remove more material than you intended!

At first I was a little disappointed that they didn’t have some kind of handle or comfort grip on them but I have to say having used them a bit I do understand why. The lack of a bulky comfort grip handle means it’s much easier to get the files into difficult to reach positions and helps in keeping the cutting face parallel to the material you are filing. The knurled section on the handles provides more than enough purchase to keep them secure in your grip and avoid slippage.

All in all very pleased with such a simple tool and if and when these do require replaced, which I cant see happening for a very long time, I would definitely want to replace them with like for like.

Advertisements

Ultrasonic Cleaner


So this weekend I got to use my new ultrasonic cleaner. This was a purchase bought on by the failure of the ultrasonic transducer in my old machine so a new unit was ordered and arrived during the week.

My previous cleaner was one of the plastic ones with its own first name that you will see in many places around the internet for about £30 delivered, usually advertised for cleaning jewelery etc and it failed after around 18 months of infrequent use so I was a little disappointed.

With this failure though I decided to have a look at some of the more robust or industrial looking units out their when I came across this GT Sonic 2 ltr Ultrasonic Cleaner with built in heater on offer at an online retailer. It was the inclusion of the heater that first attracted me to the unit as my old unit said that it should only be used with cold water which isn’t condusive to optimal results from an ultra sonic which usually perform at their best above 40 Celcius.

Well the little brown box arrived a week sooner than I had expected and the unit was resonably packaged. In the box you get the cleaner itself, mains powercord and wire basket which is fitted with brackets to hold the basket off the bottom of the tank that fold inside the basket for storage and a lid that just sits on the top

The tank itself is not very large really  measuring 150x140mm and approx 100mm deep but this is plenty big enough for cleaning a stripped down airbrush. If you are looking to clean larger items the units are available in other sizes up to 6ltr capacity I beleive. On the front of the unit you have the seperate controls for setting the desire temperature up to a max temp of 80C and the timer which can be set to a maximum of 99min (although the manual says not to run for more than 60min continuously, theres also on off switches for each. The casing of the unit is metal and it sits on 4 rubber feet.

Using the unit I straight away noticed a difference from my old cleaner in that the ultrasonics seemed much more poweful, I beleive this is probably due to the frequency the ultrasonics is running at, 40khz, I think the larger units are fitted with multiple transducers but I beleive that this one is only fitted with a single transducer, but it is plenty powerful enough and a little louder than my previous cleaner. The temperature quickly rose to the 45C I had set and actually increased a few degrees above this I suspect due to the heat being generated by the transducer.

I’ve cleaned a couple of airbrushes that had been a little neglected and had only had a flush clean at the end of the last few sessions instead of a full strip and brush clean and the unit easily got all the little deposits that were left inside to break free from the brushes and they were soon looking as clean as I had ever seen them.

So first impressions are this is a very well built machine that works very well indeed and due to the fact I was able to secure this unit on offer meant I only paid £5 more than I did for the previous unit it is replacing and it has a much better level of performance. If I do encounter any problems I will let you know.

Tamiya Modeller Sidecutters


As a side from my builds I recently picked up a pair of these Tamiya Modellers Side Cutters or sprue cutters as they are sometimes called on a visit to my local model shop and I am that impressed thought I would post about them.

I was always skeptical about these when I saw them on the shelves of the model stores as they seemed so expensive, especially compared with my cheapo Draper cutters I had been repurposing as sprue cutters but I have to say these are worth every penny.

They feel solid and extremely well made, the handles are nicely moulded and don’t feel like the plastic is going to come off in your hand whilst you’re using them. The cutting edges are extremely sharp and the blades are narrow enough to get fairly close to the model part but easily avoid cutting too close and damaging the part.

I know theres nothing exciting about sprue cutters but if your in the market to get a new pair or are looking to upgrade your existing set then you could do a lot worse than to pick a pair of these up. They really do make the tedious task of removing parts from the sprues a little less tedious!